Basic Tools Needed for Predrilled Pipe Kits

[DGErwin11]

I came up with this to answer questions often asked about what is needed to carve a pre-drilled kit (stummel and stem) into a pipe. I concentrated on tools, not techniques. This list is for those of you who want to make a pipe just for the fun of it, but not mortgage the house to buy tools. You can do that later if the bug bites you hard.

Carving your own is basically 2 sets of operations. 1) removing non pipey material & 2) shaping smoothing and finishing.

GOTTA HAVES. Well maybe one or two items you don't gotta have, but you do want to finish this decade, right?
A way to hold the block. This can be a vice, c-clamps or a dowel the same diameter as the chamber.
A coping saw. Much quicker than files for removing excess briar.
Files. To fine tune the shape. Combo flat/half round double cut, single cut, round.
Sandpaper. Depending on your filing skills, start with either 80 or 120 grit. And then all the grits (do not skip any) up to 600. (One technique thingy. Cut your sandpaper into 3/4'' strips and back them with electrical tape or you get confetti. Another very helpful item is a sanding sponge. You can wrap any grade of sandpaper around a sanding sponge and you've created a "soft-backed" sanding pad. They're sweet.
A way to make the stem shiny. This could be as simple and cheap as a 7 way finger nail buffing stick from the dollar store, but you'd be better off with MicroMesh sanding pads and a buffing setup (like the PIMO setup).
Appropriate measuring devices like calipers and 6'' rules.
Computer, tablet or smart phone. Lots of good and informative video tutorials on YouTube.
NICE TO HAVES
I found a Black & Decker WorkMate bench close to indispensable.
Electric drill. Can be used for shaping with a 5'' sanding pad and disks. Also as a buffer. Use a separate wheel for each compound. Use a plastic zip tie for speed control.
Chainsaw files in a couple of different diameters.
Needle files.
Dust mask.
Kemper ZigZag Saw K-31
DAMNED NEAR USELESS
Dremel .
Any kind of handheld power saw. And dangerous.
Conventional wood carving chisels. Briar is much too hard.
WHERE TO GET THIS STUFF
Harbor Freight. DGE really likes their files. harborfreight.com
ACE Hardware
Home Depot
Lowe's
Pipemaker's Emporium http://www.pipemakers.org/
PIMO http://www.pimopipecraft.com/ (Their book is informative)
Tim West http://jhlowe.com/toc.htm
You will notice I have not mentioned staining, shellac, rustication etc. Those topics not essential to carving a pipe. This list is for what you need to turn a lump of wood with 2 holes into a vaguely pipe shaped object. Finishing can be as simple as applying a coat of carnuba wax with a buffer or Paragon or Halycon with a rag.Or as complex as eleventy coats of various stains and then coated with diluted shellac.

[Branzig]

Great post!

[Branzig]

Really glad you added it here.

[Bruck]

Tnx Doug - I've been toying with pipe making lately; I'll share with the group if/when I produce anything presentable

I picked up one of those pre-drilled briars but haven't taken the plunge yet on carving it.

[DGErwin11]

What happened to the original post?

[Nature]

What happened to the original post?

I think for the first ten posts or so that include links or images go into a moderation mode in order to cut down on spammers.
It seems when it was edited, it went back into a moderated post.
Should be fixed now.

[DGErwin11]

Thanks. My fragile ego took a major hit.